Driver Support Document

Marconi switches, Fore series

Show Tested Devices Grid

SYSOID Mapping
SYSOID MODEL OS VERSION
 1.3.6.1.4.1.326.2.2 atmSwitch 6.2, 8.0
 1.3.6.1.4.1.326.2.2.1 software 6.2, 8.0
 1.3.6.1.4.1.326.2.2.2 hardware 6.2, 8.0
 1.3.6.1.4.1.326.2.2.4 ASX200WG 6.2, 8.0
 1.3.6.1.4.1.326.2.2.5 ASX200BX 6.2, 8.0
 1.3.6.1.4.1.326.2.2.6 ASX200BXE 6.2, 8.0
 1.3.6.1.4.1.326.2.2.8 ASX1000 6.2, 8.0
 1.3.6.1.4.1.326.2.2.17 ASX1200 6.2, 8.0
 1.3.6.1.4.1.326.2.2.18 ASX4000 6.2, 8.0
 1.3.6.1.4.1.326.2.2.22 ASX150 6.2, 8.0

Driver Features Support Grid

Driver FeaturesAccess Methods
(X signifies feature support)CLISNMPTFTPCLI+TFTPSNMP+TFTPFTPCLI+FTPSNMP+FTPCLI+SFTPSCPCLI+SCPSNMP+SCPHTTP/HTTPS
X Driver Discovery   X X                      
X General Access release notes
(CLI protocols: telnet, ssh1, ssh2, console)
X     X                  
Configuration
X Retrieve Running Configuration   X     X                  
  Retrieve Startup Configuration                            
  Retrieve Binary Configuration                            
X Device information parsing  
X Enhanced Layer2 Basic IP information parsing  
X Configuration Deployment to Running release notes       X                  
X Configuration Deployment to Startup (with reboot)         X                  
  Binary Configuration Deployment                            
Diagnostics
X Routing Table   X                        
  OSPF Neighbors                            
X Interfaces   X                        
  Modules and Inventory                            
  Flash Storage Space                            
  File System                            
X Uptime     X                      
X ICMP Test   X                        
  Topology Parsing                            
  Duplex Parsing                            
  Enhanced VLAN Parsing  
Features
  Software Center                            
  Software Image Synchronization                            
X Password Management  
(Can modify: limited username, limited password, full username, full password, read-only community strings, read/write community strings) 		X                        
X Syslog Configuration and Change Detection   Syslog patterns X                        
X Custom Scripts and Diagnostics  
X                        
  ACL Parsing  
  ACL Provisioning                            
  VLAN Provisioning                            
  Configlet Parsing  
  QoS Parsing  
  VRF Parsing  
  Context Management                            

General Access

Release Notes

Authentication failures may result from too many open sessions

Prior to version 8.0, the Marconi Fore OS supported only one session per device (after 8.0 it allows two). If the maximum number of sessions are already established, any subsequent attempt to connect to the device will result in a failure to connect. This failure will appear in NAS as an authentication error. In fact, however, the authentication information used by NAS may be acceptable, but the device does not have any sessions available.

return to top

Configuration Deployment to Running

Release Notes

Deployment to running configuration may not apply all configuration changes

Some configuration commands on Marconi Fore devices will not take effect until after a reboot takes place. Therefore, attempts to deploy to the device's running configuration may not apply all desired changes to the configuration. You should use the Deploy to startup config and reboot option to deploy configurations if you believe there is a chance some of the commands you are deploying may not take effect without a reboot. to

return to top

Syslog Triggering

return to top